Admin

Este número de error significa que la llave ya ha sido utilizada.

Hi! Make sure that you have you installed Microsoft C++ packages as it was written in the instruction.

Here are some possible reasons why your printer prints blank forms after activating the firmware: https://youtu.be/my58sHb9z5k

Hello! You should convince that you install the chipless firmware in NORMAL mode instead of UPDATE mode. Please read the instruction from our website carefully: https://inkchip.net/download/INKCHIP Instruction Method 14 (for 99 firmware).pdf Also, please watch the video guide from our official YouTube channel: https://youtu.be/oF0DsDVPT7k Let me know the result! If it will be any troubles,write us! Thank you!

Here are some possible reasons why your printer prints blank forms after activating the firmware: https://youtu.be/my58sHb9z5k

Have you activated the key successfully?

Hi! Your original firmware cannot be downgraded to earlier versions, and our chipless firmware is an earlier version. Basic concepts of the solution: - Standard InkChip firmware. Chipless firmware, which must be loaded into the printer using Firmware Mode. - 99 InkChip firmware. Chipless firmware, which must be loaded into Normal Mode. - Firmware Mode - special mode for updating printer firmware, which is activated when a certain buttons combination is pressed. - Normal Mode - normal mode of operation of the printer, simple switching on the printer with the power button. Algorithm for solving the problem: 1. Check and memorize the firmware version of the printer. The firmware version displayed is the original non-update version. 2. Flash printer 99 with InkChip firmware in Firmware Mode. 3. When trying to activate the firmware with the Activation program and the activation code, the program will generate the Reading failed 1. 4. Start flashing the printer 99 again with InkChip firmware in Firmware Mode. When the firmware status in Firmware Mode reaches 100%, and the printer display finishes counting the percentage of the firmware status, you need to pull out the power cable of the printer. 5. Connect the power cable and turn on the printer. Recovery Mode will appear on the display. 6. Flash the printer with Inkchip firmware in Recovery Mode. 7. Check the firmware version of the printer. The firmware version displayed must be different from the non-renewable firmware version. This version is the chipless firmware version of InkChip. 8. Activate chipless firmware with the key. This is just an example of a process, it doesn't matter what model of printer you have. Please watch the video on our official YouTube channel: https://www.youtube.com/watch?v=h7qWYWjMNFQ And after that just ran again the inkchip firmware upload in normal mode.

Hi! You can find the firmware and instructions for your model on our website: https://inkchip.net/soft/

Hola Póngase en contacto con nuestro equipo de soporte en este correo electrónico, ellos lo ayudarán: support@inkchip.net

Hi! Please contact our support team via this email, send them the screenshot of the error you face: support@inkchip.net

Hi! Unfortunately, we don’t have solution for this model.

First of all, please make sure that you have Microsoft Visual C++ 2017 Redistributable Package x86 and x64 installed : https://support.microsoft.com/en-us/help/2977003/the-latest-supported-visual-c-downloadsDownload the utility in one of the four languages here: https://inkchip.net/wic/Watch the video guide on our official YouTube channel to see how WIC reset utility is easy to use: https://youtu.be/VSgxJvVKV_k

You need to make sure that when you install the firmware, you disconnect the printer's network connection to your computer and only use the usb cable.

Does your computer see your printer in the "devices and printers" menu? You may have enabled the printer's network connection to your computer during the firmware installation. Make sure it was turned off and you only used the usb cable.

Hi! Unfortunately, we don’t have chipless firmware for ET series. But this model is supported by the WIC reset utility.

You have to have Windows version lower then 11(10 and earlier),are you? If no,please,try activation on computer with lower Windows version.

This might be because there are too many printers on devices and printers. That’s what might help you: close the Activator Software, turn off your printer, go to PC and remove all printers that may be in "Devices and Printers", then turn your printer on and it will install again, then open the launcher software again and it might appear normally.

Hi! Please tell me your printer model. What mode did you install the firmware in? Normal mode or update mode?

Hi! Please try this new file for you. https://inkchip.net/download/INKCHIP.net_Firmware_99_WF2850_v1.rar 1) Upload firmware which I sent 2) Switch on in normal mode(!!!!) just turn on button . - dont put printer in Program Update mode. (no need to press few buttons while turn on the printer) The uploading process will stuck at 70-80% - it is ok! Open task manager and stop updater process. Printer will blink for about 5-15 minutes - then will power OFF. Now power on the printer - chipless firmware is installed in your printer! ——— Also, this might be because there are too many printers on devices and printers. That’s what might help you: close the Activator Software, turn off your printer, go to PC and remove all printers that may be in "Devices and Printers", then turn your printer on and it will install again, then open the launcher software again and it might appear normally.

Please try this new file for you. https://inkchip.net/download/INKCHIP.net_Firmware_99_WF2630_v1.rar 1) Upload firmware which I sent 2) Switch on in normal mode(!!!!) just turn on button . - dont put printer in Program Update mode. (no need to press few buttons while turn on the printer) The uploading process will stuck at 70-80% - it is ok! Open task manager and stop updater process. Printer will blink for about 5-15 minutes - then will power OFF. Now power on the printer - chipless firmware is installed in your printer!

Hi! Please tell me your order number and printer model. Could you please send the screenshot of that? Thanks

Hi! All the solutions from our website work only with Windows OS.

Please try this new file for you. https://inkchip.net/download/INKCHIP.net_Firmware_99_WF2760_v1.rar 1) Upload firmware which I sent 2) Switch on in normal mode(!!!!) just turn on button . - dont put printer in Program Update mode. (no need to press few buttons while turn on the printer) The uploading process will stuck at 70-80% - it is ok! Open task manager and stop updater process. Printer will blink for about 5-15 minutes - then will power OFF. Now power on the printer - chipless firmware is installed in your printer!

Hi! This model is supported by the WIC reset utility: https://inkchip.net/wic/

Hi! Our keys don’t have an expiration date.