reading failed - 1

[Admin 17]

9 hours ago, John Ovid said:

Hello. I have tried the above method, but still,  it says reading failed. The moment I use the activation software. Also, the normal mode does not work. It gets stuck as early as 14% and says that it does not detect the printer (unless in UPDATE MODE). Is there any workaround regarding this problem?

Hello!
What is your printer model?
Make sure you have turned off the printer's network connection to your computer and are only using a usb connection.

[John Ovid 0]

On 12/19/2022 at 1:03 AM, Admin said:

Hello!
What is your printer model?
Make sure you have turned off the printer's network connection to your computer and are only using a usb connection.

EPSON XP235A, and yes, only thru USB mode we're doing the firmware. And yet, we still encounter this problem all the time.

[Admin 17]

On 1/9/2023 at 5:02 AM, John Ovid said:

EPSON XP235A, and yes, only thru USB mode we're doing the firmware. And yet, we still encounter this problem all the time.

On 1/9/2023 at 5:02 AM, John Ovid said:

EPSON XP235A, and yes, only thru USB mode we're doing the firmware. And yet, we still encounter this problem all the time.

Try the same procedure on the another device. 
And make sure your connection is stable.

[John Ovid 0]

11 hours ago, Admin said:

 

Hello, still the same problem occurs.

By the way, I think I forgot to disclose this. In the initial work. months ago mighe be on September, it did work, for 3months, until an Epson Software/Firmware Update took place. Being the auto-updater automatically turned on, and a relative haphazardly confirming to proceed with the update. This I believe is the main reason as to why firmware for infinite ink was overwritten. 

However, what I don't understand is by even flashing the printer's firmware with the provided software, it encounters the problem mentioned above "readingh failed."

I've also followed all directed techniques, to no avail. 

[Admin 17]

You need to load the firmware without the chip and activate it with the recovery code, did you save it?

You can repair chipless firmware with recovery code which was generated during flashing.
Watch the instruction video from our official Youtube channel on how to restore chipless firmware with recovery code:

https://youtu.be/K-aunKVMb-Y

[John Ovid 0]

On 1/11/2023 at 9:18 PM, Admin said:

You need to load the firmware without the chip and activate it with the recovery code, did you save it?

You can repair chipless firmware with recovery code which was generated during flashing.
Watch the instruction video from our official Youtube channel on how to restore chipless firmware with recovery code:

https://youtu.be/K-aunKVMb-Y

Oh, so removing the ink cartridges first. But what if we forgot to save the recovery code. Is there a chance for it to work?

Edit: I sent a request in WeChat for easier conversation. Thank you!

Edited January 16, 2023 by John Ovid

[Admin 17]

On 1/16/2023 at 4:37 AM, John Ovid said:

Oh, so removing the ink cartridges first. But what if we forgot to save the recovery code. Is there a chance for it to work?

Edit: I sent a request in WeChat for easier conversation. Thank you!

We can send it to you.

please write us on support@inkchip.net

[firelion 0]

Bonjour, j'ai le meme soucis avec une xp235

[Admin 17]

21 hours ago, firelion said:

Bonjour, j'ai le meme soucis avec une xp235

Please try this updated file with the Chipless Firmware:

https://inkchip.net/download/INKCHIP.net_Firmware_99_XP235_v1.rar

1) Upload the Chipless Firmware which is attached above.

2) Turn on the printer in the NORMAL MODE (using only the power button). Do not put the printer in the UPDATE MODE.

The loading process will get stuck at 75-85% - that is OK.

3) With the use of the task manager stop the loading process.

Printer will blink for about 5-15 minutes . It should then turn off automatically.

4) Now turn on the printer - Chipless Firmware should be installed!

5) Run the Activation Software to insert your Activation Key.

Let me know the result!

Thanks!

[SCarbruce 0]

I am having the same issue with my epson-xp 4105 please help.

[Admin 17]

On 2/8/2023 at 6:53 AM, SCarbruce said:

I am having the same issue with my epson-xp 4105 please help.

Hello!
You should install the Chipless Firmware in NORMAL mode instead of UPDATE mode.

Please read the instruction from our website carefully:

https://inkchip.net/download/INKCHIP Instruction Method 14 (for 99 firmware).pdf

Also, please watch the video guide from our official YouTube channel:

https://youtu.be/oF0DsDVPT7k

Let me know the result!
Thank you!

[kaybae0922 0]

error as well when trying to activate. It defaults to a different language and closes out. XP-4100.

 

[Admin 17]

On 2/20/2023 at 1:07 AM, kaybae0922 said:

error as well when trying to activate. It defaults to a different language and closes out. XP-4100.

 

Please try to install program in normal mode .

The instruction is sent above.

[Slty 0]

can you tell me how to go in the Firmware Mode - special mode for updating printer firmware, which is activated when a certain buttons combination is pressed For epson wf-c5790

[caenegrao19@gmail.com 0]

Estou como o mesmo problema na xp-231 - "ler falhou - 1

 

[Christian Aguas 1]

Hi! I have the same problem. My printer is WF 2850.

[Admin 17]

On 7/10/2023 at 6:56 PM, Christian Aguas said:

Hi! I have the same problem. My printer is WF 2850.

https://inkchip.net/download/INKCHIP.net_Firmware_99_WF2850_v1.rar

 

1) Upload firmware which I sent. 

2) Switch on in normal mode(!!!) just turn on button . - dont put printer in Program Update mode.

 (No need to press few buttons while turn on the printer) 

The uploading process will stuck at 70-80% - it is ok! Open task manager and stop updater process. Printer will blink for about 5-15 minutes - then will power OFF. 

Now power on the printer - chipless firmware is installed in your printer!

[RedCrimson 0]

Saludos, tengo el mismo problema que se menciona antes al momento de continuar el proceso de activación el programa muestra un mensaje "Read Failed -1" 

intente utilizando esta versión de firmware que compartió https://inkchip.net/download/INKCHIP.net_Firmware_99_XP430_v1.rar

al momento de cargarlo con la impresora en modo normal, la actualización solo llega al 14% y muestra un mensaje donde dice que no puede continuar con la actualización 

[Admin 17]

13 hours ago, RedCrimson said:

Saludos, tengo el mismo problema que se menciona antes al momento de continuar el proceso de activación el programa muestra un mensaje "Read Failed -1" 

intente utilizando esta versión de firmware que compartió https://inkchip.net/download/INKCHIP.net_Firmware_99_XP430_v1.rar

al momento de cargarlo con la impresora en modo normal, la actualización solo llega al 14% y muestra un mensaje donde dice que no puede continuar con la actualización 

¡Hola! https://inkchip.net/download/INKCHIP.net_Firmware_XP430_v3.rar

1) Cargue el firmware sin chip que se adjunta arriba.

2) Encienda la impresora en el MODO NORMAL (usando solo el botón de encendido). No ponga la impresora en el MODO DE ACTUALIZACIÓN.

El proceso de carga se atascará en un 75-85 %, eso está bien.

3) Con el uso del administrador de tareas, detenga el proceso de carga.

La impresora parpadeará durante unos 5-15 minutos. Luego debería apagarse automáticamente.

4) Ahora encienda la impresora. ¡Se debe instalar el firmware sin chip!

5) Ejecute el software de activación para insertar su clave de activación.

[Cogite 0]

Hello,

I have a problem to update my XP 15000.

When it reaches 99% nothing happens during 5-10 minutes and a message saying that the firware is not installed finally appears. Printer is On and connected.

I tried to unplugged the cordon when 99% is reached but the problem remains the same.

Please, can you help me ?

[Admin 17]

On 9/20/2023 at 7:53 AM, Cogite said:

Hello,

I have a problem to update my XP 15000.

When it reaches 99% nothing happens during 5-10 minutes and a message saying that the firware is not installed finally appears. Printer is On and connected.

I tried to unplugged the cordon when 99% is reached but the problem remains the same.

Please, can you help me ?

Stop the boot process at 75-85% through the task manager. Don’t let it get 99% and error.

[theshak10 0]

Efectivo el procedimiento de instalar la V1 del firmware que el ADMINISTRADOR recomienda en esta página, todo el proceso me funcionó para epson XP 241, incluso esperé a que terminará de cargar y me dijo que no se podía cargar el firmware, pero la apagué y si lo tomó y ya la pude recuperar con la llave de recuperación, gracias.

[addy 0]

Hi! I uploaded the firmware from your website and it's working.  Rading failed 1 appears on the screen and I can't activate the key.

epson xp2200

[didoche 0]

Hello,

I uploaded the firmware from your website on my XP 2200 and it's working, got 100 % (same firmware)

but when i want to activate online i have  Raeding failed 1 appearing on the screen and I can't activate the key.

do you have some kind of firmware update other then V1 ?

[Admin 17]

On 2/23/2024 at 5:19 PM, didoche said:

Hello,

I uploaded the firmware from your website on my XP 2200 and it's working, got 100 % (same firmware)

but when i want to activate online i have  Raeding failed 1 appearing on the screen and I can't activate the key.

do you have some kind of firmware update other then V1 ?

You should convince that installed the Chipless Firmware in NORMAL mode instead of UPDATE mode.

Please read the instruction from our website carefully:

https://inkchip.net/download/INKCHIP Instruction Method 14 (for 99 firmware).pdf

Also, please watch the video guide from our official YouTube channel:

https://youtu.be/oF0DsDVPT7k