EPSON WF-2861

[bee 0]

Hi can i know if the activation is supporting epson wf2861 ( singapore set ) 

thanks. 

[bee 0]

i got this msg and stuck at 99%. 

my printer model is 2861, does 2860 and 2861 use the same firmware installer? 

thanks. 

 

[bee 0]

hi admin, 

any updates? 

thanks, 

[Admin 17]

Hi!

Yes, if works for your model. have you been trying to install the firmware in the normal mode? 

[Ricky Fai 0]

After clicked the "INKCHIP.net_Activation.exe", got error message window- just a code, not understand. After click OK, program window closed and nothing happen. What should be done?

Edited August 4, 2023 by Ricky Fai

[Admin 17]

Please try this new activator:

https://inkchip.net/download/activation.rar

[Ricky Fai 0]

Same. After close and re click the exe file again, can show English language, and click "activate online", error message " Wrong ID code". Also your whatsapp no. cannot be used 

[Admin 17]

4 hours ago, Ricky Fai said:

Same. After close and re click the exe file again, can show English language, and click "activate online", error message " Wrong ID code". Also your whatsapp no. cannot be used 

Could you please make a short videо where we can see how you install the firmware and send it to us at: support@inkchip.net.

 Thank you!

[Ricky Fai 0]

Hi, Firmware upload to printer is no problem (shown 100% done and success), but go to activation got problem. Need to re-do the firmware uploading again? Video for activation problem sent to you already

[Admin 17]

10 hours ago, Ricky Fai said:

Hi, Firmware upload to printer is no problem (shown 100% done and success), but go to activation got problem. Need to re-do the firmware uploading again? Video for activation problem sent to you already

The load should not get to 100% when installing in normal mode. Most likely you are doing something wrong.

[Ricky Fai 0]

According to the download instruction, it shall be 100%. If not, what should be the correct procedure?

[Admin 17]

In the video guide it shows that you don't need it to load 100%. When the load gets stuck at 75-85%, that's okay! You will need to pull the cable out at that point and put it back in.

Then turn the printer on just using the power button.

Watch the video please:

 

 

 

[Ricky Fai 0]

Hi, both the video and manual said " if loading stop before reach 100%"; But my case was that it did not stop (only holding for a few seconds at certain time).

Is it meaning that I have to unplug the power cord at certain % of loading?

I have sent you the screw video of uploading firmware. Pls check

[Admin 17]

6 hours ago, Ricky Fai said:

Hi, both the video and manual said " if loading stop before reach 100%"; But my case was that it did not stop (only holding for a few seconds at certain time).

Is it meaning that I have to unplug the power cord at certain % of loading?

I have sent you the screw video of uploading firmware. Pls check

Hello!

About this issue, we have already replied to you on email.

Thank you!

[Ricky Fai 0]

Replied, awaiting your further instruction

[Ricky Fai 0]

Any update?

[Admin 17]

On 8/15/2023 at 4:27 AM, Ricky Fai said:

Any update?

Let it stop the download process through the task manager and proceed to activation.

[Ricky Fai 0]

Finally successfully do the activation, and can do normal printing already. Thanks for Admin guiding patiently...

[Admin 17]

Glad to hear it!

Thank you!