van

The software for the 2150 model is definitely not compatible.Waste of money. I purchased a license because at first it was advertised as compatible and listed on the software page,now it is removed after the devs realized they just tried passing a related model's flash as an actual solution. as you can see by the dislikes on YouTube that is the case with other printers as well and I'm tired of this back and forth conversation with useless suggestions and vague 'tips'. I want a refund on my order as I have lost valuable time, left with a printer that recognizes no cartridges and had to purchase a new and expensive printer cause of my work. all I got was mumbo jumbo, not that I even got to activate anything as nothing was working anyway so I demand a full refund so I don't have reasons to expose you as a fraudulent operation. REFUND my FAULTY UNACTIVATED software that will not work even though I was assured it would ASAP so I can be on my way cause I have work to do and no time for this.. If you do it then you can delete my posts, delete my account do as you wish.

How do I 'restart' the printer

yes the process never makes it to 100% even if I plug and unplug

Doesn't work. It throws an error at 99% I remove the plug and retry just in case then it throws the same error so after that I try the other 'unofficial' method of ending the process via task bar after it resets but stalls at around 80% at which point if I let it as per forum instructions it wont gο into flashing mode, it won't go into flashing mode either if i press the triangular 'cancel' key as per instructions posted on YouTube.

failure tο flash

Administrator mode, with antivirus and firewall turned off

In any device and with any configuration ending the task will not get the printer to go into flashing mode.. Perhaps we should also press some key combo on the printer to initialize it?

the computer connects properly to the address via telnet but the activation throws a 10060 error but the upload program doesn't manage to flash the printer anyway, even if I interrupt the process before some error flag is triggered at 70 to 80% the printer never goes into 'flashing lights mode' to indicate that the upload was successful and that it installed the new firmware..

Will try this guide

The issue really is that the printer never goes blinking after the uploading process like something went wrong there, that issue persists.

Still same result

nope firewall and antivirus off still same error

will try perhaps it was a firewall

If I attempt to activate online I get communication error 10060

Yes. it's order Order #425199.

Still not working. Can you walk me through the steps in case I am doing something wrong and the flasher has done its job right? If it's a flasher error advise on the resolution of that problem instead. I tried putting the randomly generated key alone as well as the whole string and still nothing.

I am experiencing the same issue with an XP-2150 and no standard procedure will work or even SuziniNC's suggestion

My printer is the XP-2150. The firmware program always gets stuck at 99% even if I unplug the printer then turn it back on. I always run it on regular mode and the program on administrator mode with antivirus turned off. This makes no sense..

I am however experiencing the issue where the flasher is stuck at 99% even after unplugging and turning on the printer on regular mode..

I apologize for the trouble and I am embarassed to badmouth your effort! I accidentally misclicked a software link for another series, the correct compatible software is coded correctly and is working!

After inquiring about the compatibility of your software solution for an EPSON XP-2150 I purchased the key for the aforementioned printer. I understand a generic firmware coded for another printer is used for several compatible printers of the same series but this one is not even recognized while trying to install the firmware. I have followed both the .pdf manual and the youtube tutorial and attempted installation by the book at which point the installation never gets past the '"The printer is not connected or the connected printer is not the target printer". As a programmer myself I would rather not fish for any compensation but only get a solution to my problem as I have prepaid a non-functioning software advertised to be compatible. If you have used a generic edited code for a semi-compatible printer that is not a solution unless it works 100% of the time at which point there is no point in sticking with a non-working software paid with my hard-earned money. Thanks for your preoccupation with my issue in advance. software error screen