Jump to content
Maggy

No instruction for WF-2850

Recommended Posts

Hi, when opening the pdf file with the instructions for the Work Force 2850, I got this file:

"Instructions for updating the printer firmware in chipless, method 9 Compatible Epson Printer Models: WF-2630; WF-2631; WF-2650; WF-2651; WF-2750; WF-2751; WF-4630; WF5620; PX-M840F"

NO 2850 mentioned...

How do I enter firmware mode for the Epson WF-2850?

Thank you.

Share this post


Link to post
Share on other sites

Hello!
Please try this new file for you:
 
https://inkchip.net/download/INKCHIP.net_Firmware_99_WF2850_v1.rar
 
1) Upload firmware which I sent
2) Switch on in normal mode(!!!) just turn on button . - dont put printer in Program Update mode. (No need to press few buttons while turn on the printer)
The uploading process will stuck at 70-80% - it is ok!
Open task manager and stop updater process.
Printer will blink for about 5-15 minutes - then will power OFF.
Now power on the printer - chipless firmware is installed in your printer!

Share this post


Link to post
Share on other sites

Hi,

I was correct in that the printer could NOT be updated due to the non-Epson print cartridges were still in the printer, (and thus Epson was complaining).

Once I purchased Epson cartridges, the process began as one would expect!

Problem now is, per directions above, the update did NOT get stuck between 70/80%, instead the update ran till about 98% and then complained it had not been successful??

Please assist!!

 

Share this post


Link to post
Share on other sites
2 hours ago, Murphs.World@verizon.net said:

Hi,

I was correct in that the printer could NOT be updated due to the non-Epson print cartridges were still in the printer, (and thus Epson was complaining).

Once I purchased Epson cartridges, the process began as one would expect!

Problem now is, per directions above, the update did NOT get stuck between 70/80%, instead the update ran till about 98% and then complained it had not been successful??

Please assist!!

 

 

IMG_2309.JPG

IMG_2310.JPG

IMG_2313.JPG

IMG_2312.JPG

Share this post


Link to post
Share on other sites
Hello!
Please try this new file for you:
 
On 4/14/2021 at 4:38 AM, Murphs.World@verizon.net said:

Final portion of the update, hits 99% complete....and then fails!

 

Please help!!!

IMG_2317.JPG

IMG_2316.JPG

Your original firmware cannot be downgraded to earlier versions, and our chipless firmware is an earlier version. Basic concepts of the solution:
- Standard InkChip firmware. Chipless firmware, which must be loaded into the printer using Firmware Mode.
- 99 InkChip firmware. Chipless firmware, which must be loaded into Normal Mode.
- Firmware Mode - special mode for updating printer firmware, which is activated when a certain buttons combination is pressed. 
- Normal Mode - normal mode of operation of the printer, simple switching on the printer with the power button.
Algorithm for solving the problem:
1. Check and memorize the firmware version of the printer. The firmware version displayed is the original non-update version.
2. Flash printer 99 with InkChip firmware in Firmware Mode.
3. When trying to activate the firmware with the Activation program and the activation code, the program will generate the Reading failed 1.
4. Start flashing the printer 99 again with InkChip firmware in Firmware Mode. When the firmware status in Firmware Mode reaches 100%, and the printer display finishes counting the percentage of the firmware status, you need to pull out the power cable of the printer.
5. Connect the power cable and turn on the printer. Recovery Mode will appear on the display.
6. Flash the printer with Inkchip firmware in Recovery Mode.
7. Check the firmware version of the printer. The firmware version displayed must be different from the non-renewable firmware version. This version is the chipless firmware version of InkChip.
8. Activate chipless firmware with the Activation program.
 
https://inkchip.net/download/INKCHIP.net_Firmware_99_WF2850_v1.rar
 

This is just an example of a process, it doesn't matter what model of printer you have. Please watch the video on our official YouTube channel:

And after that just ran again the inkchip firmware upload in normal mode.

 
 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...